Product Range

One family of fluids, engineered for every process temperature.

Every grade below is built around the same principle: protect the metals in the loop while carrying heat efficiently, for long enough that you stop thinking about the fluid at all. Each card shows its operating range and typical application first talk to our technical team for a system-specific recommendation.

Modified-diol family

ET-4 Series

Our core secondary refrigerant and heat-transfer fluid family. Formulated from a modified diol base with a corrosion inhibitor, biostat, solubiliser and water-stabiliser package, ET-4 fluids replace inhibited ethylene-glycol and carry heat in both directions across a single closed loop.

ET-4
Standard grade
Operating range−35 to +50°C
ApplicationHVAC chilled-water loops, general industrial process cooling

The workhorse grade, with broad compatibility across stainless steel, carbon steel and copper.

Non-DG
ET-4G
High-temperature variant
Operating range−35 to +150°C
ApplicationHotter HVAC and industrial loops needing the same corrosion protection above +50°C

The same modified-diol chemistry as ET-4, reformulated to hold up under sustained high-temperature operation.

Non-DGHigh-temperature
ET-4A
Food-grade raw materials
Operating range−30 to +100°C
ApplicationFood & beverage processing, cold-storage loops with incidental food-contact risk

Manufactured with food-grade raw materials and very low acute oral toxicity.

Non-DGFood-grade raw materials
ET-4D-YE
Low conductivity, no inorganic salt
Operating range−35 to +130°C
ApplicationBESS cold-plate cooling loops

Formulated without inorganic salts for low electrical conductivity. Compatible with stainless steel, carbon steel, copper and aluminium.

Low conductivityAluminium-safe
ET-4D
Ultra-low conductivity
Operating range−35 to +100°C
ApplicationSensitive electronics, cold-plate battery cooling where stray current matters as much as heat transfer

The lowest-conductivity grade in the range, with no inorganic salts.

Ultra-low conductivityAluminium-safe

Organic acid salt family

ET-8 Series

A potassium-formate, water-based heat-transfer fluid delivering stronger thermal performance than glycol or calcium chloride, with no flash point and no flammability classification.

ET-8
Non-flammable, no flash point
Operating range−50 to +50°C
ApplicationPharmaceutical, ground freezing, refrigeration, wind tunnels

An alternative to calcium chloride, trichloroethylene, methylene chloride and silicone fluids.

Non-flammableNo flash point
ET-8G
High-temperature variant
Operating range−50 to +100°C
ApplicationHigher-temperature pharma and process duty needing ET-8's non-flammable profile

The same organic acid-salt chemistry as ET-8, reformulated for high-temperature systems.

Non-flammableHigh-temperature
ET-8L
Aluminium-safe variant
Operating range−50 to +50°C
ApplicationSame duty as ET-8, in systems with aluminium components

The same organic acid-salt chemistry as ET-8, reformulated for systems containing aluminium components.

Non-flammableAluminium-safe

Fluorinated dielectric family

ET-14 Series

A colourless, non-conductive, non-flammable dielectric fluid family for direct-immersion cooling and very-low-temperature process duty, spanning seven grades from −110°C up to +135°C.

ET-14 A–G
Perfluorocarbon dielectric
Operating range−110 to +135°C
ApplicationData-centre immersion cooling, semiconductor manufacturing, hydrogen & lithium-battery testing, cryogenic process control

Electrically non-conductive with no flash point. Enables PUE below 1.1 in immersion-cooled deployments.

DielectricNon-DG

High-temperature family

ET-16C & ET-17

For processes that run hot rather than cold: ET-16C is a single-fluid hydrocarbon heat carrier stable up to +340°C, and ET-17 is a hydrocarbon dielectric fluid for data-centre immersion duty.

ET-16C
High-temperature heat carrier
Operating range−30 to +340°C
ApplicationPharmaceutical, chemical, solar-thermal, oil & gas process heating

A modified synthetic hydrocarbon heat-transfer fluid with good thermal stability and minimal metal corrosion.

Single-fluidClosed-loop system
ET-17 A/B/C
Hydrocarbon dielectric
Operating range−50 to +107°C
ApplicationData-centre server immersion cooling

Non-corrosive to electronic components, with good resistance to acid and sludge formation over time. Pour point −40 to −50°C and closed-cup flash point 107–138°C, grade-dependent — full operating range to be confirmed with our technical team for your specific duty.

DielectricNon-DG

Quick reference

Grade selection at a glance

For a full technical data sheet and material safety data sheet on any grade, contact our technical team.

GradeOperating rangeKey traitApplication
ET-4−35 to +50°CStandard, broadest metal compatibilityHVAC & general process cooling
ET-4G−35 to +150°CHigh-temperature variant of ET-4Hotter HVAC & industrial loops
ET-4A−30 to +100°CFood-grade raw materialsFood & beverage, cold storage
ET-4D-YE−35 to +130°CLow conductivity, aluminium-safeBESS cold-plate cooling
ET-4D−35 to +100°CUltra-low conductivitySensitive electronics, battery cooling
ET-8 / ET-8L−50 to +50°CNon-flammable, no flash pointPharma, refrigeration, ground freezing
ET-8G−50 to +100°CHigh-temperature variant of ET-8Higher-temperature pharma & process duty
ET-14 series−110 to +135°CDielectric, non-conductiveData centre immersion, cryogenic process
ET-16C−30 to +340°CSingle-fluid, high temperaturePharma, chemical, solar-thermal, oil & gas
ET-17 series−50 to +107°C*Hydrocarbon dielectricData centre server immersion

* ET-17 series operating range is grade-dependent; +107°C is the series maximum. Talk to our technical team for a system-specific recommendation.

ET-17 figure derived from pour point and flash point data; full operating range to be confirmed with our technical team.

Not sure which grade fits your system?

Share your process temperatures, materials of construction and current fluid, and we'll recommend a grade with a lab sample to test before you commit.

Scroll to Top